In the supply chain world, we talk about “scaling.” You start with what you need today, but you plan for what you might need tomorrow. A few years ago, buying a standard Two-Car Carport was the perfect solution. It kept the hail off your sedan and the sun off your dashboard. It was cost-effective and efficient.
But needs change. Maybe that sedan has been replaced by a classic car restoration project. Maybe your “storage” has expanded to include expensive power tools, gym equipment, or inventory for a small business. Suddenly, an open-air structure isn’t enough. You need security. You need climate control. You need a Metal Garage.
As the Supply Chain Director, I oversee the movement of steel framing and sheet metal across the country. One of the most frequent requests we see isn’t just for new buildings—it’s for “add-on” kits to enclose existing ones. Converting a carport into a garage is a brilliant logistical move. You utilize the existing skeleton (the roof and legs) and simply add the skin (side panels) and organs (doors and windows).
However, it is not as simple as just screwing on some metal sheets. It requires structural calculations, understanding local zoning, and precise material ordering. In this guide, we will break down the conversion process from a materials and logistics perspective, ensuring you get the Custom Garage you need without buying a whole new building.
Phase 1: The Structural Audit
Before we ship a single sheet of steel to your driveway, you must perform a structural audit of your current Metal Carport. Not all carports are candidates for conversion. When you enclose a building, you fundamentally change how physics interacts with it. An open carport lets wind pass through it. An enclosed garage must withstand the full force of the wind pushing against it (Wind Load).
1. Check Your Anchors
Your current anchoring system might be sufficient for a carport, but is it ready for a garage?
- Dirt/Gravel: If you used rebar anchors, you will likely need to upgrade to mobile home auger anchors to handle the increased wind shear.
- Concrete: Ensure you have adequate wedge anchors installed.
2. Leg Height and Clearance
This is the number one logistical error we see in Garagen-Bausätze zum Selberbauen. If you have a 6-foot leg height on your carport, and you want to install a 7-foot garage door, the math doesn’t work. You generally need a leg height that is at least 1 foot taller than your desired garage door height.
3. Steel Gauge Assessment
Check your paperwork or measure your frame thickness.
- 14-Gauge: Standard for most carports. Suitable for conversion in moderate climates.
- 12-Gauge: Thicker, stronger, and carries a higher wind/snow rating. Highly recommended if you are enclosing a structure in areas with heavy weather.
| Feature | 14-Gauge Tubular Steel | 12-Gauge Tubular Steel |
|---|---|---|
| Thickness | 2.5 inches x 2.5 inches | 2.25 inches x 2.25 inches (Thicker Walls) |
| Garantie | Standard (Often 10-20 Years) | Extended (Often 20-50 Years) |
| Strength | Standard Tensile Strength | ~30% Stronger Tensile Strength |
| Am besten für | Standard Carports, RV Covers | Enclosed Garages, Workshops, Industrial |
| Kosten | Baseline | +10% to 15% Premium |
Phase 2: Navigating the Permit Process
Logistics isn’t just about moving trucks; it’s about moving paperwork. In many municipalities, a carport is considered a “temporary structure,” while a garage is a “permanent accessory structure.” This distinction changes the legal requirements.
Do not skip this step. I have seen customers forced to tear down perfectly good 2-Car Garages because they skipped a $50 permit.
The “Change of Use” Permit
You are technically changing the classification of your building. Your local building inspector will want to know:
- Snow Load: Can the roof hold the snow now that the building is heated? (Heat loss can cause melting and refreezing/ice dams).
- Wind Load: Can the new walls withstand 100+ mph gusts?
- Stiftung: Is the slab thick enough? (Usually 4 inches minimum for a garage).
Permit Checklist for Conversion:
| Document/Requirement | Beschreibung | Why It Matters |
|---|---|---|
| Plot Plan | A drawing showing where the structure sits on your land relative to property lines. | Zoning laws often require enclosed structures to be further from the property line than open ones. |
| Engineer Drawings | Certified blueprints of the frame and anchoring. | Proves to the city that our steel structures meet safety codes. We can provide these. |
| Anchor Specs | Details on how the building is secured to the ground. | Ensures the “sail effect” of the new walls won’t rip the building out of the ground. |
| HOA Approval | Letter of acceptance from your Homeowners Association. | HOAs often hate galvanized steel. You may need to color-match siding to your house. |
Phase 3: Framing and Materials (The Kit)
When you order a conversion kit from us to turn your Wohnmobil-Carport into an Wohnmobil-Garage, you aren’t just buying sheets of metal. You are buying a framing system.
Horizontal vs. Vertical Siding
This is a critical aesthetic and structural decision.
- Horizontal: The ridges run front-to-back. This is cheaper because we can run the sheet metal the full length of the building. However, dirt builds up in the ridges.
- Vertical: The ridges run up-and-down. This requires us to install “hat channel” or horizontal purlins between the legs to have something to screw the panels into. It is stronger and stays cleaner, but costs more due to the extra framing steel.
The Material Pick List
If you are doing this as a Build-It-Yourself project, here is what your shipment will likely contain. We organize our pallets to ensure you have exactly what you need.
| Material Component | Function | Quantity Estimation |
|---|---|---|
| Side Panels | The “skin” of the walls (29-gauge or 26-gauge steel). | Based on perimeter length ÷ 3ft (standard panel width). |
| Gable Ends | Triangular panels to close the space under the roof peak at the front and back. | 2 per building (Front and Back). |
| J-Trim | Protective trim for the bottom of panels and around doors. | Perimeter length + Door perimeters. |
| L-Trim / Corner Trim | Covers the sharp corners where side walls meet end walls. | 4 lengths (one for each corner). |
| Hat Channel (Optional) | Horizontal bracing needed if you choose Vertical Siding. | Depends on wall height and spacing. |
| Self-Tapping Screws | Color-matched screws with neoprene washers to seal out water. | Calculate ~40 screws per sheet of siding. |
| Frame Tubing | Extra 2.5″ square tubing to frame out garage doors and walk-in doors. | Dependent on number of openings. |
Phase 4: The Cost Breakdown
This is the question every Supply Chain Director gets asked: “Is it cheaper to convert my carport or just buy a new garage?”
Generally, converting saves you about 30-40% compared to buying a brand-new structure, assuming your existing frame is in good condition. You are saving the cost of the roof arches, the main legs, and the roof panels—which are the most expensive components.
However, costs vary wildly based on the “commodities market.” Steel prices fluctuate. The following breakdown is an estimate based on current market averages for a standard 20×20 Two-Car Carport conversion.
Cost Breakdown Table (20×20 Unit)
| Cost Category | Item Description | Estimated Cost (DIY) | Estimated Cost (Pro Install) |
|---|---|---|---|
| Materials: Siding | 3 sides enclosed (assuming 1 side attached or open) + Gable ends. | $1,500 – $2,200 | $1,500 – $2,200 |
| Materials: Doors | 1 Roll-up Garage Door (8×7) + 1 Walk-in Door. | $600 – $1,200 | $600 – $1,200 |
| Materials: Framing | Extra tubing for door headers and wall supports. | $300 – $500 | $300 – $500 |
| Labor | Installation crew fees. | $0 (Your Sweat Equity) | $1,000 – $1,500 |
| Erlaubt | City/County fees. | $50 – $200 | $50 – $200 |
| Stiftung | Concrete slab pouring (if not already present). | $2,000 – $3,500 | $2,000 – $3,500 |
| Total Estimated | Base Conversion Cost | $4,450 – $7,600 | $5,450 – $9,100 |
Note: These prices are estimates. Custom Carports with unique dimensions will require custom quotes.
The “Hidden” Costs of Conversion
In supply chain, we call these “accessorials.” They are the little things that add up.
- Freight: Shipping a pallet of siding costs money. If you can combine this with a neighbor’s order or pick up from a local distribution center, you save.
- Isolierung: As mentioned in our previous blog “Insulated Garages 101,” adding insulation adds cost but saves money long-term.
- Leveling: If your carport has settled and is unlevel, you cannot install rigid siding. You may need to jack up the legs and pour concrete footers first.
Phase 5: Design and Customization Options
Just because you are converting an existing structure doesn’t mean it has to look like a patchwork quilt. Modern Metall-Carport-Bausätze allow for seamless integration.
Color Matching
We use standard industrial color codes. If you bought your carport 5 years ago, the “Barn Red” or “Slate Blue” we sell today is likely the exact same paint code. However, be aware of UV Fading. Your existing roof may have faded slightly in the sun. When you install brand new side panels, there might be a slight contrast.
- Profi-Tipp: Choose a contrasting color for the walls! If you have a white roof, go for dark grey walls. It looks intentional and modern (the “Barndominium” look) and hides the fade difference.
Platzierung der Tür
When framing out your 3-Auto-Garage conversion, think about flow.
- Side Entry: Do you want a walk-in door on the side so you don’t have to open the big bay door every time you need a screwdriver?
- Drive-Through: For Boat Garages, consider putting a roll-up door on both the front and back. This allows you to pull the boat straight through without having to back it out—a logistical dream for boat owners.
Windows and Light
Metal garages can be dark caves. We recommend installing at least two 30″x30″ windows for cross-ventilation and natural light.
- Security Note: If you are storing valuable Motorrad-Garage items, place windows high up (clerestory style) so light gets in, but prying eyes can’t see the goods.
Phase 6: DIY vs. Professional Conversion
Can you do this yourself? Absolutely. The beauty of our products is that they are essentially giant erector sets.
The DIY Path:
- Tools Needed: Impact driver, magnetic drill bits, tin snips/metal shears, level, ladder, and safety gloves (sheet metal edges are razor sharp).
- Skill Level: Moderate. If you can frame a deck, you can enclose a carport.
- Time: A weekend for two people to enclose a standard 20×20 unit.
The Professional Path:
- Why Hire Pros? Siding installation is an art. Getting the corners tight, the trim flush, and the screws perfectly aligned requires practice. If you want your Custom Garage to look showroom ready, professional installers are worth the labor cost. They also carry insurance if they scratch a panel or hurt themselves.
Conclusion: Securing Your Assets
Converting a carport to a garage is one of the smartest upgrades you can make to your property. It increases your property value, secures your assets, and gives you a year-round workspace.
From a supply chain perspective, it is efficient. You are reusing existing steel and upgrading its utility. Whether you need a secure Ein-Auto-Garage for your daily driver or a massive Wohnmobil-Garage workshop, the conversion process is straightforward if you plan the logistics.
Ready to start your conversion? We need a few things from you:
- Current photos of your carport (all 4 sides).
- Measurements (Width, Length, and Leg Height).
- Your zip code (for wind/snow load calculations).
Contact our team today. Let’s turn that open canopy into the workshop of your dreams.
Frequently Asked Questions (FAQ)
Q: My carport is on dirt. Can I still enclose it? A: Yes, but we highly recommend pouring a concrete footing or a full slab first. If you enclose a dirt-floor carport, you will have significant moisture and dust issues inside. At a minimum, you must upgrade your dirt anchors to mobile home anchors.
Q: Can I add a lean-to to my carport at the same time I enclose it? A: Absolutely. This is a very common request. We can ship the framing for a “lean-to” addition along with your siding kit. This effectively turns a 2-Auto Carport into a 3-Auto-Garage (2 enclosed, 1 open lean-to).
Q: Will the new metal match my old metal? A: If you bought the carport from us, the paint codes are likely the same. However, if your carport is 10+ years old, we recommend sending us a physical chip of the paint so we can check for fading or supplier changes.
Q: Do I need to dismantle the carport to enclose it? A: No! That is the beauty of conversion. The roof stays up. We simply frame between the existing legs. It is a non-intrusive construction process.
